A tensile testing machine performs the most fundamental and common types of mechanical testing. A tensile test applies tensile (pulling) force to a material and measures the specimen's response to the stress. By doing this, tensile tests determine how strong a material is and how much it can elongate. Tensile tests are typically conducted on electromechanical or universal testing machines, are simple to perform, and are fully standardized.
TENSILE TESTING MACHINE
Components and Parts
Tensile tests are performed on tensile testing machines, also known as universal testing machines. A tensile testing machine consists of a test frame that is equipped with a load cell, testing software, and application-specific grips and accessories, such as extensometers. The type of material being tested will determine the type of accessories needed, and a single machine can be adapted to test any material within its force range simply by changing the fixturing.
|Tensile Testing Machine|
Tensile testing machine load frames can come in single or dual column configurations depending on their force capacity.
Test software is where operators can configure test methods and output results.
The load cell is a transducer that measures the force applied to the test specimen. Instron load cells are accurate down to 1/1000 of load cell capacity.
|4)||Grips and Fixtures
A wide range of specimen grips and fixtures are available to grip test specimens of different materials, shapes, and sizes.
Some test methods require measurement of a specimen's elongation under load. Instron's AVE2 can measure changes to specimen length down to ±1 µm or 0.5% of reading.
Tensile testing machines are available in a variety of different sizes and force capacities ranging from 0.02 N to 2,000 kN. Most low force testing is performed on an electromechanical single-column or dual-column tabletop machine, while higher force applications require floor model frames. Instron's 6800 Series systems are available in capacity ranges up to 300 kN and can perform a wide range of different test types, including tensile, compression, bend, peel, tear, shear, friction, torsion, puncture, and more. Instron's Industrial Series servohydraulic systems are designed for even higher capacity testing of high strength metals, alloys, and advanced composites.
TENSILE TESTING STANDARDS
Standards for Testing Plastics, Elastomers, and Metals
Most tensile testing is performed to established standards published by standards organizations such as ASTM and ISO. Testing standards prescribe acceptable test parameters and results for different types of raw materials such as metals, plastics, elastomers, textiles, and composites, as well as for finished products such as medical devices, automotive parts, and consumer electronics. These standards ensure that materials and products entering the supply chain display predictable mechanical properties and are not likely to fail in their expected end use. Since the cost and safety implications of product failure cannot be overstated, companies are encouraged to invest in high-quality, accurate testing equipment that is designed to help them easily determine whether or not their products meet applicable standards.
TENSILE TEST DATA ANALYSIS
Understanding the Mechanical Properties of Materials
Measuring a material or product in tension allows manufacturers to obtain a complete profile of its tensile properties. When plotted on a graph, this data results in a stress/strain curve which shows how the material reacted to the forces being applied. While different standards require the measurement of different mechanical properties, the greatest points of interest are usually the point of break or failure, modulus of elasticity, yield strength, and strain.
Ultimate Tensile Strength
One of the most important properties we can determine about a material is its ultimate tensile strength (UTS). This is the maximum stress that a specimen sustains during the test. The UTS may or may not equate to the specimen's strength at break, depending on whether the material is brittle, ductile, or exhibits properties of both. Sometimes a material may be ductile when tested in a lab, but, when placed in service and exposed to extreme cold temperatures, it may transition to brittle behavior.Hooke's Law
For most materials, the initial portion of the test will exhibit a linear relationship between the applied force or load and the elongation exhibited by the specimen. In this linear region, the line obeys the relationship defined as "Hooke's Law" where the ratio of stress to strain is a constant, or . E is the slope of the line in this region where stress (σ) is proportional to strain (ε) and is called the "Modulus of Elasticity" or "Young's Modulus."Modulus of Elasticity
The modulus of elasticity is a measure of the material's stiffness which only applies in the initial linear region of the curve. Within this linear region the tensile load can be removed from the specimen and the material will return to the exact same condition it had been in prior to the load being applied. At the point when the curve is no longer linear and deviates from the straight-line relationship, Hooke's Law no longer applies, and some permanent deformation occurs in the specimen. This point is called the "elastic or proportional limit." From this point on in the tensile test, the material reacts plastically to any further increase in load or stress. It will not return to its original, unstressed condition if the load is removed.Yield Strength
A material's "yield strength"is defined as the stress applied to the material at whichplastic deformation starts to occur.Offset Method
For some materials (e.g. metals and plastics), the departure fromthe linear elastic region cannot be easily identified. Therefore an offset method to determine the yield strength of the material is allowed. This methodology is commonly applied when measuring the yield strength of metals. When testing metals according to ASTM E8/E8M, an offset is specified as a percentage of strain (usually 0.2%). The stress (R) that is determined from theintersection point "r" when the line of the linearelastic region (with slope equal to Modulus of Elasticity) isdrawn from the offset "m" becomes the Yield Strengthby the offset method.Alternate Moduli
The tensile curves of some materials do not have a very well-definedlinear region. In these cases, ASTM Standard E111 provides foralternative methods for determining the modulus of a material,as well as Young's Modulus. These alternate moduli are thesecant modulusand tangent modulus.Strain
We will also be able to find the amount of stretch or elongation that the specimen undergoes during tensile testing. This can be expressed as an absolute measurement in the change in length or as a relative measurement called "strain." Strain itself can be expressed in two different ways, as "engineering strain" and "true strain." Engineering strain is probably the easiest and the most common expression of strain used. It is the ratio of the change in length to the original length, . The true strain is similar, but based on the instantaneous length of the specimen as the test progresses, , where Li is the instantaneous length and L0 the initial length.
View our Tensile Testing and Tensile Testing Machines FAQ for additional information