ISO 13934-1 Tensile Properties of Fabrics

ISO 13934-1 provides a testing procedure for determining the tensile properties of fabrics. This standard mainly applies to woven textile fabrics, but can also be applicable to fabrics produced using other techniques. it is not normally applied to woven elastic fabrics, geotextiles, nonwoven fabrics, coated fabrics, textile-glass woven fabrics, fabrics made from carbon fibers, or polyolefin tape yarns. Since this testing can be performed on a vast range of fabrics, it is used across a wide range of industries. This standard uses a strip method of testing to measure maximum force as well as elongation at maximum force. If required, it also records the force at rupture and elongation. Two sets of specimens are prepared, one in the warp direction and one in the weft direction.

ISO 13934-1

Materials Testing System 

As with most textiles testing, a high data rate is key to capturing good results. To consistently and accurately measure the tear strength of your material, it is important to remember that the data sampling rate needs to be high enough that the test peaks and troughs are adequately captured. Because of this we recommend a high tier system such as Instron's 6800 Series, which comes equipped with a 5 kHz data acquisition rate. For most testing to ISO 13934-1 a single column frame is appropriate, as the loads rarely rise above 5 kN.  Instron’s Bluehill® Universal software can be equipped with a test method suite that provides pre-built calculations for ISO 13934-1 to help simplify testing and ensure compliance.




ISO 13934-1 Test Setup
1) 68SC-5 Universal Testing System
2) Bluehill Universal Software
3) 2580 Series Load Cell
4) 2712-045 Pneumatic Side-Action Grips

 

ISO 13934-1 test setup
Grips and Accessories

Instron's pneumatic side action grips with rubber faces are well suited for gripping nearly all types of fabric specimens when testing to ISO 13934-1. While manual action grips can also work, pneumatic side action grips are often preferred due to their ease of use, productivity, and better repeatability. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage. ISO 13934-1 calls for smooth and flat jaw faces for testing, but this largely depends on the material being tested. In some cases, serrated or wave profile jaw faces may be more appropriate for preventing slippage while testing and are allowable per the standard when smooth or flat jaw faces cannot hold the specimen until break. Wave profile faces increase the clamping surface area per unit height and are intended to help grip some of the most difficult textile materials through failure. In some cases, serrated jaw faces may be more appropriate for preventing slippage while testing. The standard also calls for the use of extra material within the jaw faces such as paper or medium grit emery cloth for some fabrics as an additional way to help prevent slippage when necessary.

2712-045
5 kN Model | 2712-045
Related Content

6800 Serie – Broschüre für Premium-Testsysteme

Universal-Testsysteme der Instron Serie 6800 bieten unvergleichliche Genauigkeit und Zuverlässigkeit. Die 6800 Serie basiert auf einer zum Patent angemeldeten Operator-Protect-Systemarchitektur mit einem brandneuen Smart-Close Air Kit und Collision-Mitigation-Funktionen, wodurch Materialtests einfacher, intelligenter und sicherer sind als je zuvor.

Broschüre Bluehill Universal

Bluehill Universal wurde von Grund auf für haptische Interaktion und eine intuitive Benutzererfahrung ausgelegt. Entdecken Sie einfacheres und schnelleres Prüfen mit Funktionen wie vorgeladene Prüfmethoden, QuickTest in Sekunden, verbessertem Datenexport und Instron Connect, einer neuen Funktion, die eine direkte Verbindung zum Service bereitstellt. Benutzer früherer Versionen von Software wie Bluehill 2 und Bluehill 3 können leicht auf die neueste Version von Bluehill aufrüsten.

2712-04X Serie – Seitlich wirkende, pneumatische Spannzeuge

Seitlich wirkende, pneumatische Spannzeuge sind eine vielseitige Lösung zum Einspannen vieler Materialien. Bewertete Kapazitäten zwischen 1 und 10 kN.