ASTM F88 Seal Strength of Flexible Barrier Materials

How to Perform an ASTM F88 Peel Test on Packaging

Written by Jonathan Camara

In the medical device and packaging industries, sterilization is a big concern. Whether a device is disposable or intended to be re-sterilized and re-used, all medical packaging must have seals strong enough to protect the sterility of the product while also being easy for healthcare providers to open. In order to ensure that packaging achieves this delicate balance, many manufacturers follow testing standards such as ASTM F88 to measure the tensile strength of the adhesives used in medical device packaging. This guide is designed to introduce you to the basic elements of an ASTM F88 peel test and will provide an overview of the equipment, software, and samples needed. However, anyone planning to conduct ASTM F88 testing should not consider this guide an adequate substitute for reading and following the full standard.

What Does it Measure?

ASTM F88 measures the peel strength of packaging in one of two peel configurations under normal ambient temperatures. It does NOT measure the peel strength of packaged products, such as a sterile packaged syringe. Testing a packaged product is often useful for companies, but is considered outside of the scope of ASTM F88.

ASTM F88 is conducted on a universal testing machine (also called a tensile testing machine) at a rate between 200 and 300 mm/min (8 to 12 in/min). The standard calls for the calculation of two measurements:

Average Seal Strength - The average force per specimen adhesion width throughout the peel test.

Maximum Seal Strength - The maximum force point recorded per specimen adhesion width that occurs during the peel test.

Both of these calculations are determined by analyzing data points acquired during each test. The standard recommends that these calculations be applied between 10% and 90% of the total acquired points. 

Bluehill Universal ASTM F88 test results

Tensile Testing System

A standard package for testing to ASTM F88 includes a 3400 Series or 6800 Series single-column tensile tester with a load cell capacity between 5 N and 5 kN (1.1 lbf to 1124 lbf). The 34SC-5 model features a 1000 Hz data acquisition rate and a +/- 0.5% accuracy specification down to 1/200th of load cell capacity. For customers looking for higher force accuracy and data acquisition rates, Instron's 68TM-5 features a 5,000 Hz data acquisition rate and a +/- 0.5% accuracy specification down to 1/1000th of load cell capacity.

 ASTM F88 test setup

ASTM F88 Test Setup

1. Instron 3400

2. Bluehill Universal Dashboard (2490-696)

3. 2530 Series Load Cell

4. 2710-112 Screw Side-Action Grips


Both the 3400 and 6800 Series testing machines can be purchased with Instron's Bluehill® Universal Software and Operator Dashboard. The Adhesives and Biomedical packages within Bluehill Universal come with pre-loaded test methods for many standards, including ASTM F88. For customers who need to meet 21 CFR Part 11 compliance, Bluehill Universal's Traceability Module allows full visibility into all test system activity and allows users to prove it during an audit.

Bluehill Universal Screen Shot
Specimens and Specimen Measurement

Of the two testing configurations (T-Peel or 180° peel), there are three specimen holding methods: two for T-Peel and one for 180° peel. Each specimen is self-adhered to an alignment plate and then secured in an upper and lower grip for testing.

ASTM F88 gripping techniques

T-Peel "Technique A" - This configuration is a standard T-peel application where the adhered section is left unsupported while the specimen is under test.

T-Peel "Technique B" - This configuration is similar to Technique A; however, the adhered part of the specimen is supported by hand.

180° Peel "Technique C" - Technique C involves adhering one side of the specimen to a substrate or alignment plate for a 180° peel test. The side with the plate is inserted in the upper grip, while the other end of the specimen is secured in the bottom grip.

To ensure conformance with the standard, all specimens which need to be cut for testing shall be done so in accordance with ASTM D882, which is the testing standard for tensile strength and elongation of thin film. Specimens must be cut to a width of 25mm (0.984 in), 15mm (.5971 in), or 25.4mm (1.0 in).


There are two gripping solutions for this standard, depending on needs for ease of use, throughput, and the ability to offset alignment for 180° peel tests. In both cases, rubber-coated grip faces should be used so as to avoid tearing the delicate specimen. Jaw faces are available in many different sizes and are easily interchangeable.

Advanced screw side action grips provide a standard solution for each configuration outlined in ASTM F88. They are easily opened and closed with the use of screws on each side of the grip. In the case of 180° peel applications, either the upper or lower grip faces can be offset to account for the thickness of the substrate, or alignment plate.

Pneumatic side action grips provide an advanced solution for T-Peel specimens and improve throughput with the use of a pneumatic footswitch.

Both options can be fitted with specimen centering devices to ensure proper alignment for each test.
250 N Model | 2712-052
500 N Model | 2710-112
Variations in Data

Because ASTM F88 involves very low forces, test results can be easily affected by small details. For example, customers who prop up the tail of the specimen by hand (T-Peel Technique B) or use some other device to support the tail will see different results from those who test without providing any sort of tail support. Likewise, it is important to make sure that load cell cables and pneumatic grip hoses are properly clipped to the crosshead before testing, as hanging cords produce drag forces that can adversely effect test results. Though attention to detail and consistency is always important, the extremely low forces involved in ASTM F88 testing means that operators must be especially careful to control all possible adverse forces that might influence their results. 

Lastly, there will be variation between different brands of testing systems due to the different data acquisition systems used. This paper describes how Instron handles data rate and bandwidth, and how these settings effect peel test results.

Related Content

6800 Catálogo de sistemas de ensayo Serie Premier

Los sistemas de ensayo universales Serie 6800 de Instron proporcionan una precisión y fiabilidad sin igual. Construida sobre una arquitectura de sistema Operator Protect pendiente de patente, con un kit Smart-Close totalmente nuevo y funciones de mitigación de colisiones, la Serie 6800 hace que los ensayos de materiales sean más sencillos, limpios y seguros que nunca.

Catálogo de Bluehill Universal

El software Bluehill Universal está diseñado desde el principio para una interacción táctil y una experiencia de usuario intuitiva. Descubre ensayos más sencillos y limpios con funciones como métodos de ensayo precargados, QuickTest en segundos, exportación de datos mejorada e Instron Connect, una nueva función que proporciona un enlace de comunicación directa con el servicio. Los usuarios de versiones anteriores del software, como Bluehill 2 y Bluehill 3, pueden actualizarse fácilmente a la última versión de Bluehill.

Serie 3400: soluciones de ensayo asequibles

Sistemas de ensayo universales Serie 3400 de Instron para ensayos de tracción, compresión, doblado y otros materiales.

Mordazas neumáticas de acción lateral Serie 2712-04X

Las mordazas neumáticas de acción lateral ofrecen una solución de agarre versátil para una amplia gama de materiales. Capacidades nominales entre 1 y 10 kN.

Serie 2710 Mordazas de acción de tornillo

Las Mordazas de acción de tornillo proporcionan un método sencillo y eficaz para sujetar muestras de ensayo en una amplia gama de aplicaciones.