BS EN 1719 Tack Measurement for Pressure Sensitive Adhesives

envelopes and tensile grips

BS EN 1719 determines the “loop tack” measurement for coated pressure-sensitive adhesives. This standard is primarily used by manufacturers of paper and board, packaging, and disposable sanitary products to measure the strength of things such as envelope adhesives and diaper tab adhesives. To create specimens for this test, adhesive strips are formed into a loop and gripped together. The adhesive loop is brought down into contact with a flat rigid plate at a rate of 5 mm/s. When the loop contacts the plate over approximately 25 mm by 25 mm, the adhesive loop is pulled upwards at a rate of 5 mm/s and the maximum force to fully separate the loop from the plate is recorded.

Materials Testing System

Instron’s 6800 Series frames enable data capture of up to 2.5 kHz to ensure that all fast-changing test events are captured. Too low of a bandwidth may “dull” the results and lead to a missed peak, resulting in artificially lower loop tack values. System capacity will depend on the strength of the elastomer; however most tests to this standard will be very low force, making this application perfect for a single column frame (34SC or 68SC).  




BS EN 1719 Test Setup
1) 6800 Series Universal Testing System
2) Bluehill Universal Software
3) 2580 Series Load Cell
4) 2712-041 Pneumatic Side Action Grips

 

materials testing system
Grips

Pneumatic side action grips prevent specimen slippage by maintaining a constant clamping pressure throughout testing. These are available in capacities from 50 N up to 10 kN, but BS EN 1719 only requires the very lowest end of this force spectrum. Both pneumatic and advanced side action grips feature quick-change jaw faces that can be easily changed to accommodate different materials.

50 N Model | 2712-051
2712-052
250 N Model | 2712-052
Testing Tips and Tricks
  • Bluehill Universal is provided with one free application module upon purchase. Each module contains pre-configured test methods and supporting documentation to assist with testing to various standards, including BS EN 1719, which is part of the Adhesives module. Please note that this method requires the use of TestProfiler.
  • To read this standard in full, purchase BS EN 1719.
Related Content

Catálogo de sistemas de ensayo Serie 6800 Premier

Los sistemas de ensayo universales Serie 6800 de Instron proporcionan una precisión y fiabilidad sin igual. Construida sobre una arquitectura de sistema Operator Protect pendiente de patente, con un kit Smart-Close totalmente nuevo y funciones de mitigación de colisiones, la Serie 6800 hace que los ensayos de materiales sean más sencillos, limpios y seguros que nunca.

Serie 3400: soluciones de ensayo asequibles

Sistemas de ensayo universales Serie 3400 de Instron para ensayos de tracción, compresión, doblado y otros materiales.

Catálogo de Bluehill Universal

El software Bluehill Universal está diseñado desde el principio para una interacción táctil y una experiencia de usuario intuitiva. Descubre ensayos más sencillos y limpios con funciones como métodos de ensayo precargados, QuickTest en segundos, exportación de datos mejorada e Instron Connect, una nueva función que proporciona un enlace de comunicación directa con el servicio. Los usuarios de versiones anteriores del software, como Bluehill 2 y Bluehill 3, pueden actualizarse fácilmente a la última versión de Bluehill.

Mordazas neumáticas de acción lateral Serie 2712‑04X

Las mordazas neumáticas de acción lateral ofrecen una solución de agarre versátil para una amplia gama de materiales. Capacidades nominales entre 1 y 10 kN.

Mordaza de acción de tornillo serie 2710

Las Mordazas de acción de tornillo proporcionan un método sencillo y eficaz para sujetar muestras de ensayo en una amplia gama de aplicaciones.