ASTM D5035 Breaking Strength and Elongation of Textile Fabrics (Strip Method)

ASTM D5035 textile testing

 ASTM D5035 provides a testing procedure for determining the maximum force and elongation at maximum force of various textile fabrics using raveled strip and cut strip methods of testing. If required, the force and elongation at rupture are recorded as well. 

The raveled testing method is mainly applicable to woven fabrics, whereas the cut strip test is mainly applicable to nonwoven, dipped or coated fabrics, and felted fabrics. However, the methods from this testing procedure are not meant for knitted fabrics or others with high breaking elongation. It is important to review the full standard in order to fully understand the test setup, procedure, and results requirements.

Materials Testing System

As with most textiles testing, it is important to consider data rate when choosing a testing instrument. To consistently and accurately measure the tear strength of your material, it is important to remember that the data sampling rate needs to be high enough that the test peaks and troughs are adequately captured. We recommend Instron’s high tier 6800 Series systems due to their data capture rate of up to 5 kHz. For most textile fabrics testing to ASTM D5035, a single column frame is appropriate as the loads rarely go above 5 kN.




ASTM D5035 Test Setup
1) 6800 Series Universal Testing System
2) Bluehill Universal Software
3) 2580 Series Load Cell
4) 2712-045 Pneumatic Side Action Grips

 

ASTM D5035 system setup
Grips 

Specimens tested to ASTM D5035 are paired with adequate grips utilizing jaw faces that include a minimum width at least 10 mm wider than the width of the specimen with a minimum height of 25 mm. Though manual grips are acceptable, pneumatic side action grips are recommended due to their ease of use, high repeatability, and high throughput. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage.

ASTM D5035 calls out utilizing smooth and flat jaw faces for testing, but this primarily depends on the material being tested. Rubber coated jaw faces are often the first choice, and in some cases where the fabric specimen is strong or slippery, serrated jaw faces may be more appropriate. The standard also calls out the ability to use extra padding material within the jaw faces such as paper or emery cloth as an additional way to help prevent slippage.

2712-045
5 kN Model | 2712-045
Tips and Tricks
  • This standard recommends a Constant Rate of Extension (CRE) frame for testing, however, it also notes that Constant Rate of Load or Constant Rate of Traverse are acceptable as well. When different testing machines are used for testing the same materials, a constant time-to-break of 20 +/- 3 seconds is recommended for the most comparable results. It should be noted that results still can vary significantly based on the frame used.
  • ASTM D5035 requires that two sets of specimens are prepared, one in the warp direction and one in the weft direction.
  • Instron’s Bluehill Universal testing software has advanced pre-built methods available with pre-configured calculations helping to ensure compliance to ASTM D5035.

Related Content

6800 Opuscolo sui sistemi di test Premier della serie

I sistemi di test universali della serie 6800 di Instron offrono precisione e affidabilità impareggiabili. Grazie alla serie 6800, costruita sulla base di un’architettura di sistema in attesa di brevetto e dotata delle nuovissime funzionalità Smart-Close Air Kit e Collision Mitigation, i test dei materiali non sono mai stati così semplici, intelligenti e sicuri.

Opuscolo su Bluehill Universal

Bluehill Universal Software è realizzato appositamente per l’interazione touch e un’esperienza utente intuitiva. Scopri test più semplici e più intelligenti con funzionalità quali i metodi di test precaricati, QuickTest in pochi secondi, esportazione di dati migliorata e Instron Connect, una nuova caratteristica che fornisce un collegamento diretto di comunicazione con l’Assistenza. Gli utenti delle versioni precedenti del software come Bluehill 2 e Bluehill 3 possono facilmente aggiornarle alla versione più recente di Bluehill.

Prese pneumatiche ad azione laterale serie 2712-04x

Le prese pneumatiche ad azione laterale forniscono una soluzione versatile per la presa di una vasta gamma di materiali. Capacità nominali tra 1 e 10 kN.