ASTM F88 Seal Strength of Flexible Barrier Materials
Written by Jonathan Camara
- Peel, Tear and Friction
- ASTM F88
In the medical device and packaging industries, sterilization is a big concern. Whether a device is disposable or intended to be re-sterilized and re-used, all medical packaging must have seals strong enough to protect the sterility of the product while also being easy for healthcare providers to open. In order to ensure that packaging achieves this delicate balance, many manufacturers follow testing standards such as ASTM F88 to measure the tensile strength of the adhesives used in medical device packaging. This guide is designed to introduce you to the basic elements of an ASTM F88 peel test and will provide an overview of the equipment, software, and samples needed. However, anyone planning to conduct ASTM F88 testing should not consider this guide an adequate substitute for reading and following the full standard.
ASTM F88 measures the peel strength of packaging in one of two peel configurations under normal ambient temperatures. It does NOT measure the peel strength of packaged products, such as a sterile packaged syringe. Testing a packaged product is often useful for companies, but is considered outside of the scope of ASTM F88.
ASTM F88 is conducted on a universal testing machine (also called a tensile testing machine) at a rate between 200 and 300 mm/min (8 to 12 in/min). The standard calls for the calculation of two measurements:
Average Seal Strength - The average force per specimen adhesion width throughout the peel test.
Maximum Seal Strength - The maximum force point recorded per specimen adhesion width that occurs during the peel test.
Both of these calculations are determined by analyzing data points acquired during each test. The standard recommends that these calculations be applied between 10% and 90% of the total acquired points.
Tensile Testing System
A standard package for testing to ASTM F88 includes a 3400 Series or 6800 Series single-column tensile tester with a load cell capacity between 5 N and 5 kN (1.1 lbf to 1124 lbf). The 34SC-5 model features a 1000 Hz data acquisition rate and a +/- 0.5% accuracy specification down to 1/200th of load cell capacity. For customers looking for higher force accuracy and data acquisition rates, Instron's 68TM-5 features a 5,000 Hz data acquisition rate and a +/- 0.5% accuracy specification down to 1/1000th of load cell capacity.
ASTM F88 Test Setup
1. Instron 3400
2. Bluehill Universal Dashboard (2490-696)
3. 2530 Series Load Cell
4. 2710-112 Screw Side-Action Grips
Both the 3400 and 6800 Series testing machines can be purchased with Instron's Bluehill® Universal Software and Operator Dashboard. The Adhesives and Biomedical packages within Bluehill Universal come with pre-loaded test methods for many standards, including ASTM F88. For customers who need to meet 21 CFR Part 11 compliance, Bluehill Universal's Traceability Module allows full visibility into all test system activity and allows users to prove it during an audit.
Of the two testing configurations (T-Peel or 180° peel), there are three specimen holding methods: two for T-Peel and one for 180° peel. Each specimen is self-adhered to an alignment plate and then secured in an upper and lower grip for testing.
T-Peel "Technique A" - This configuration is a standard T-peel application where the adhered section is left unsupported while the specimen is under test.
T-Peel "Technique B" - This configuration is similar to Technique A; however, the adhered part of the specimen is supported by hand.
180° Peel "Technique C" - Technique C involves adhering one side of the specimen to a substrate or alignment plate for a 180° peel test. The side with the plate is inserted in the upper grip, while the other end of the specimen is secured in the bottom grip.
To ensure conformance with the standard, all specimens which need to be cut for testing shall be done so in accordance with ASTM D882, which is the testing standard for tensile strength and elongation of thin film. Specimens must be cut to a width of 25mm (0.984 in), 15mm (.5971 in), or 25.4mm (1.0 in).Grips
There are two gripping solutions for this standard, depending on needs for ease of use, throughput, and the ability to offset alignment for 180° peel tests. In both cases, rubber-coated grip faces should be used so as to avoid tearing the delicate specimen. Jaw faces are available in many different sizes and are easily interchangeable.
Advanced screw side action grips provide a standard solution for each configuration outlined in ASTM F88. They are easily opened and closed with the use of screws on each side of the grip. In the case of 180° peel applications, either the upper or lower grip faces can be offset to account for the thickness of the substrate, or alignment plate.
Pneumatic side action grips provide an advanced solution for T-Peel specimens and improve throughput with the use of a pneumatic footswitch.Both options can be fitted with specimen centering devices to ensure proper alignment for each test.
Because ASTM F88 involves very low forces, test results can be easily affected by small details. For example, customers who prop up the tail of the specimen by hand (T-Peel Technique B) or use some other device to support the tail will see different results from those who test without providing any sort of tail support. Likewise, it is important to make sure that load cell cables and pneumatic grip hoses are properly clipped to the crosshead before testing, as hanging cords produce drag forces that can adversely effect test results. Though attention to detail and consistency is always important, the extremely low forces involved in ASTM F88 testing means that operators must be especially careful to control all possible adverse forces that might influence their results.
Lastly, there will be variation between different brands of testing systems due to the different data acquisition systems used. This paper describes how Instron handles data rate and bandwidth, and how these settings effect peel test results.Related Content
I sistemi di test universali della serie 6800 di Instron offrono precisione e affidabilità impareggiabili. Grazie alla serie 6800, costruita sulla base di un’architettura di sistema in attesa di brevetto e dotata delle nuovissime funzionalità Smart-Close Air Kit e Collision Mitigation, i test dei materiali non sono mai stati così semplici, intelligenti e sicuri.
Bluehill Universal Software è realizzato appositamente per l’interazione touch e un’esperienza utente intuitiva. Scopri test più semplici e più intelligenti con funzionalità quali i metodi di test precaricati, QuickTest in pochi secondi, esportazione di dati migliorata e Instron Connect, una nuova caratteristica che fornisce un collegamento diretto di comunicazione con l’Assistenza. Gli utenti delle versioni precedenti del software come Bluehill 2 e Bluehill 3 possono facilmente aggiornarle alla versione più recente di Bluehill.
Le prese pneumatiche ad azione laterale forniscono una soluzione versatile per la presa di una vasta gamma di materiali. Capacità nominali tra 1 e 10 kN.
Le prese a vite ad azione laterale forniscono un metodo molto semplice ed efficiente per tenere i provini di test e possono essere utilizzate in una vasta gamma di applicazioni.