ISO 8295


ISO 8295 Coefficient of Friction Plastic Film and Sheeting


ISO 8295 is a standardized test method used for determining static (μ_s ) and kinetic (μ_k ) coefficients of friction of plastic film and sheeting. Plastic film is a widely used material in the packaging industry. Within the packaging industry the use of film can be separated into two categories: food packaging such as produce bags, carton liners, or meat seal wrap, and non-food packaging such as envelope liners or potting soil sacks. Outside of the packaging industry, plastic films are used for an assortment of products: trash bags, can liners, I.V. bags, construction liners, and other barriers. Thin films are also an important component of electric vehicle batteries, which is an industry predicted to experience explosive growth over the course of the next decade. The frictional properties of these films must be characterized and controlled to ensure the safety and functionality of the end product.

 


 


Separator Film Testing for Electric Vehicle Batteries

Separator films for electric vehicle batteries are being produced in increasingly high volumes and must undergo frictional testing as part of a robust material characterization process. These films are used to separate the anode and cathode in lithium-ion and other liquid electrolyte batteries, and are extremely critical to product safety. The most common material used for separator film is polyolefin, a polymer film that is strong enough to withstand the winding operation during assembly as well as uneven plating of lithium on the anode due to extensive use. Safer and stronger separator material more effectively prevents contact between the anode and cathode, while thinner material helps reduce the weight of each battery and improve energy density. Understanding the frictional properties of this polymer film can help ensure the material is being wound properly during assembly and will behave as expected under extensive use. Testing standards specific to electric vehicle batteries have not yet been established, so ISO 8295 is commonly used as a proxy standard to characterize the frictional properties of these materials.

Learn About Electric Vehicle Battery Testing

electric vehicle chassis
Materials Testing System

Instron’s 6800 series frames are capable of data capture up to 5 kHz to ensure that all fast-changing test events are captured. Too low of a data capture rate may lead to missed force peaks and troughs, resulting in an inaccurate average strength value. For ISO 8295 testing we recommend a 6800 series single column frame equipped with a low force (5 – 100 N) 2530 series load cell depending on the expected frictional forces. This test requires the use of Instron's 2810-005 Coefficient of Friction fixture, which is specifically designed to meet the requirements of ISO 8295 and ASTM D1895.




ISO 8295 Test Setup
6800 Series Universal Testing System
Bluehill Universal Software
2530 Series Load Cell
2810-005 Coefficient of Friction Fixture

 

ISO 8295 coefficient of friction thin films and sheeting

How to Perform a Test to ISO 8295


The ISO 8295 test method is used to investigate the static and dynamic frictional properties of film and sheet plastics when sliding against either itself or another material. This method is intended to be used for non-sticky plastic film and sheeting of up to 0.5 mm in thickness. To perform this test, the specimen is supported on a friction table consisting of a horizontal test table, a sled, and a driving mechanism which uses a pully to produce a relative motion between the sled and the test table. One piece of the specimen is attached to the table with double-sided adhesive tape while the other piece is secured to the sled in the same way. The test machine then drags the sled across the table at a constant rate of displacement, causing friction between the two pieces of material. The force is recorded, and test results are calculated. As always we suggest reviewing the full ISO 8295 standard to fully understand the testing requirements.

Tips and Tricks 

Instron’s 6800 controller can accurately measure forces down to 0.1% (1/1000th) of the 2580 series load cell's capacity, enabling the measurement of very low forces, potentially eliminating the need for multiple load cells. The lowest capacity 2580 series load cell is 500 N, meaning that it can maintain 1% accuracy from 0.5 N to 500 N. Instron’s 2530 series load cells can maintain 1% accuracy down to 1/250th of the cell’s capacity when used on a 6800 frame. The lowest capacity 2530 series load cell is 5 N, meaning it can maintain 1% accuracy from 0.02 N to 5 N. Forces beneath the lower limits of the 2580 and 2530 series cells can be measured, but Instron cannot guarantee 1% accuracy.

Related Content

3400 시리즈 - 경제적인 시험 솔루션

인장, 압축, 굽힘 및 기타 소재 특성 시험을 위한 Instron 3400 시리즈 만능 시험기.

6800 시리즈 프리미어 시험기 브로셔

Instron 6800 시리즈 만능 시험기는 최고의 정확도와 신뢰성을 제공합니다. 6800 시리즈는 완전히 새로운 Smart-Close Air Kit 및 Collision Mitigation 기능이 있는 특허 출원 중인 Operator Protect 시스템 아키텍처를 기반으로 하며, 그 어느 때보다 간편하고 스마트하며 안전한 소재 시험을 가능하게 합니다.

2530 시리즈 저하중 로드셀

Instron 2530 시리즈 로드셀은 Instron 저하중 시험기와 함께 사용하도록 특별히 설계되었습니다. 하중 용량의 범위는 ±5 ~ ±100N(0.5 ~ 10kgf, 1.12 ~ 22.5lbf)이며, 측정 범위가 넓어 로드셀 용량의 1/500까지 힘을 측정할 수 있습니다.

2580 시리즈 로드셀

Instron 2580 시리즈 로드셀은 5900 및 6800 시리즈 시험기와 함께 사용하도록 특별히 설계되었으며, 판독값의 0.5% 정확도로 용량의 1/1000만큼 낮은 힘을 측정할 수 있어서 탁월한 성능을 제공합니다.

2810-005 마찰 계수 치구

Instron의 2810-005 마찰 계수 치구는 ASTM D1894 또는 ISO 8295 표준을 이용하여 플라스틱 필름 및 시트의 정지 및 운동 마찰 계수를 측정합니다.




Contact Us