문헌
브로셔,매뉴얼,백서 및 사례 연구를 위한 문헌 라이브러리
Automated Testing System For Tensile Testing of Metals
Instron® Automated Tensile Testing Systems for metals are configured to perform unattended tensile testing of metallic specimens of varying lengths and thicknesses. Tests to ASTM E8 and EN 10002-1 standards. Includes r and n value results as well as capability of r-bar/Delta r and Bake Hardening index. Standard system capacities of 100 and 200 kN (more available upon request).
제품소개 03/21/2012 1.34 MB
Guide to High Temperature Tensile Testing
Guide to the various components of a high-temperature tensile testing system–furnaces, grips, pull rods, and extensometry. Includes an important system configuration tool.
제품소개 02/15/2012 850.35 KB
Biopuls Hip Femoral Fatigue Fixture
Simulates fatigue loading of hip ste during a gait cycle.
제품소개 02/07/2012 206.01 KB
Submersible Pneumatic Versa Grips S5054X
The Biopuls submersible pneumatic versa grips provide an easy and
efficient method for gripping test specimens, ranging
from thin film polymers to biological tissues, in a fluid
bath for tension and torsion mechanical testing.
제품소개 01/31/2012 171.93 KB
Composites Test Fixtures: Strain Gauge Adapter
These Instron strain gauge adapters measure strain in materials and structural testing using strain gauge adapters that connect a single gauge to any standard Instron strain channel. Supports 2‑ and 3‑wire gauges, provides accurate synchronous data acquisition, and includes built‑in bridge completion and calibration circuitry for use across multiple composite testing applications.
제품소개 01/27/2012 446.73 KB
Hydraulic Wedge-Action Grips
Instron® hydraulic wedge grips provide an innovative solution for high capacity testing and deliver enhanced gripping performance, usability, and operator safety.
제품소개 11/11/2011 1.03 MB
Composite Test Fixtures Two Rail Shear ASTMD4255
ASTM D 4255 describes both 2 Rail and 3 rail methods of determining the in-plane shear strength of a composite laminate panel. In the 2 Rail test (Method A) a laminate panel specimen is clamped between loading plates and yokes and then subject to shear loading. Measurement of shear strain requires the use of strain gauges on the specimen.
제품소개 06/15/2011 101.05 KB
Composites Test Fixtures Flatwise Shear ASTMC273
ASTM C 273 describes a method of determining the shear strength of a sandwich core panel. The test the specimen is bonded to thick loading plate blocks and is subject to shear loading applied via the blocks.
제품소개 06/15/2011 94.78 KB
Composites Test Fixture Compression After Impact
The “Airbus CAI” fi xture is used to test the impact resistance of carbon and other fi ber-reinforced plastic (CFRP) composite laminates. These materials are prone to great reduction in compressive strength even when the impact load is insuffi cient to cause visible damage. The post-impact compression test is used widely to assess the relative performance of different composite laminates with different fi ber matrix combinations. In the fi rst part of the test the laminates are subjected to low-velocity impact loading simulating tool drops and fl ying debris. Specimens then undergo a compression after impact(CAI) test on an electromechanical or servohydraulic testing machine.
제품소개 06/15/2011 102.73 KB
Composites Test Fixtures Climbing Drum Peel Fixtures ASTMD1781
ASTM D 1781 describes a method of measuring the strength of the adhesive bond between the core and the facing of a honeycombcore panel. The Instron® climbing drum peel fixtures meet the requirements of ASTM D 1781. Designed with a standard fitting, they can be used on any standard Instron machine. The fixtures are robust and durable, and can be used inside an environmental chamber over a wide temperature range.
제품소개 06/15/2011 127.5 KB