Literatur
Bibliothek mit Druckschriften, Handbüchern, Whitepapers & Fallstudien
Automated Plastics Testing System
The Instron® Automated Plastics Testing Systems enable a new dimension of testing productivity. Available as a complete turnkey solution or installed on an existing Instron universal testing machine, these systems have been designed to meet ASTM D638, ISO 527, ASTM D790, ISO 178, and other testing standards, including JIS and DIN.
Produkte 08/26/2014 988.57 KB
Composites Test Fixtures – Compression | Unsupported Gage Section
Compression testing of composites without anti-buckling guide plates, is often preferred as the free unsupported length is more representative of true compression behavior. This method relies on the accuracy of the alignment between the upper fixture and the lower fixture while introducing the compression load. In addition, the natural failure process of the specimen will induce high lateral forces that must be resisted to ensure that forces remain in true compression. In these principles, the IITRI, Wyoming Modified Celanese and Combined Loading Compression fixtures are the same.
Produkte 08/25/2014 750.49 KB
Anti-Buckling Compression Testing Fixture
This anti-buckling fixture is designed for compression testing of rigid plastics and the shear testing of reinforced plastics. It has also been adapted for use with high strength composites.
Produkte 08/25/2014 316.47 KB
Automated Metals Testing System
The Instron® Automated Metals Testing Systems enable a new dimension of testing productivity. Available as a complete turnkey solution or installed on an existing Instron testing machine, these systems have been designed to meet ASTM E8, EN 10002-1, ISO 6892, and other metals testing standards, including JIS and DIN.
Produkte 08/25/2014 1.36 MB
2716 Series Pneumatic Wedge Action Grips Data Sheet
The Pneumatic Wedge Action Grips, available in 100 or 200 kN, provide a convenient method of clamping both large round and flat specimen shapes, up to a 50 mm (2 in) diameter, or flat specimens up to 40 mm (1.57 in) thick respectively. V-face grips are used for round specimens by design and have a reduced area at the center that compromises their ability to absorb high-energy breaks without fracture. This grip uses a split V-face configuration that allows the break energy to be dissipated without damaging the faces.
Produkte 08/20/2014 152.52 KB
Gripping Effects in Composite Fatigue Testing
Gripping methods can significantly affect values and consistency of results in mechanical testing of composites. With a growing drive to measure and understand the dynamic behavior of composites, it is sometimes necessary to revisit previous methodologies for specimen gripping.
Whitepapers 07/31/2014 1012.66 KB
Characterizing Complex Materials with Impact Testing
During the European Congress on Composite Materials(ECCM16) seminar in Seville, Spain, Andrea Calzolari presented research that was carried out in cooperation with the University of Turin and the LIMA
Corporate Group.
Whitepapers 07/31/2014 717.75 KB
A Review of Contacting Strain Measurement Techniques for Composites Laminate Testing
The most common approaches to strain measurement in composites coupon testing involve the use of strain gauges bonded to the surface of the specimen or using a clip-on extensometer.
Whitepapers 07/31/2014 2.05 MB
Upgrade Your Drop Tower
Is your testing machine costly to maintain? Are you under pressure to automate tests and modernize reports? Then now is a
great time to consider upgrading your aging instrument for an innovative, top-of-the-line new Instron® 9350 Drop Tower.
Produkte 07/29/2014 403.08 KB
Instron Cord & Yarn Grips (2714-04x)
Instron, a leading provider of testing equipment designed to evaluate the mechanical properties of materials and components, offers an easy solution designed specifically to overcome the problem of premature failure for industrial textile fibers – including Aramid and UHMwPE.
Press Releases 07/23/2014 138.6 KB